What is the #1 Thing You Should Do When Your Garage Door Stops Working?

What is the #1 Thing You Should Do When Your Garage Door Stops Working?

Southern Illinois

Determine the Garage's Type Door and Opener


If garage doors stop functioning, it's a stressful and uncomfortable experience.Whether you're rushing for work or trying to get your car into the garage in the middle of a storm, a malfunctioning door is the last thing you need to have to deal with.The first step in addressing the issue is to determine the type of garage door and opener you are using, as this will greatly affect the way you approach fixing and troubleshooting. .


Roll-up garage doors, which are often used in commercial environments, are made from the slats, which are rolled into a coil.

Tilt-up doors, on other hand, are a single solid piece that is able to tilt out and up as it opens.

Importantly, you must identify the kind of garage door opener.The three primary types are belt-drive, chain-drive and screw-drive openers.Chain-drive openers, which use an iron chain to raise and lower the door, are long-lasting and affordable, however they can be noisy.Belt-drive openers function similarly, however they use a belt made of rubber that makes them more quiet and a great choice for attached garages.Screw-drive openers are able to move the door by means of a threaded steel rod providing a compromise between sound and cost.


The next step is to inspect your garage door opener, and identify the type. Check the plug and breaker to confirm that the opener is running. Check the release cord for manual operation to make sure that it's not been pulled. This would cause the door to become removed from the opener. Check the rollers and tracks of the door for any damage or obstructions, and then remove any obstructions.

If needed, you should lubricate the moving parts. Insufficient lubrication could cause them to become stuck or become stuck.

If the door is still unable to operate, consider resetting the opener.This can usually fix electronic malfunctions or faults.Consult your opener's manual for specific instructions for reset, since this process can vary between models.Many modern openers include a reset button, while others may require unplugging them and plugging back in.


In certain instances the problem could be more complex for instance, a damaged spring or a worn-out motor that requires professional assistance.Springs are under significant tension and could be hazardous to repair without the appropriate tools and experience.


If the garage door stops functioning then you need to speak with a professional.

Be sure to look for obstructions or debris.


If your garage door suddenly ceases functioning, it can be difficult and frustrating particularly if it's part of your daily routine.

One of the primary and most practical steps to take when faced by this issue is to check for any obstructions or debris.This easy, yet efficient action is often the most effective way to identifying the issue and then restoring function to your garage door.

Garage doors are based using a set of rollers, tracks, as well as other parts that have to be free of obstacles in order to function smoothly.Over time, dirt, leaves, small rocks or other debris could accumulate on the tracks or be stuck in the rollers.Even an obstruction of a tiny size can prevent the door from closing or opening properly.Therefore an in-depth inspection of these components should be your first course of action.


Start by inspecting the tracks on both the left and right sides of the door.

What is the #1 Thing You Should Do When Your Garage Door Stops Working? - Southern Illinois

  1. ethnicity
  2. leadscrew
  3. mile
Find obvious obstructions, or debris accumulation. If you spot something odd, such as a twig, or a rock that is stuck within the track. Get it removed with care.

Sometimes, the issue might not be evident immediately, so it's advisable to run your hands along the track in order to feel for any unnoticed obstacles.Ensure that the tracks are aligned correctly too, since a an incorrect alignment can cause the door to be jammed.

After that, check the rollers and hinges.These parts should move freely without resistance.If they are sticky or stuck, it could be a sign of accumulated dirt or rust.In such cases cleaning them and applying lubrication will usually resolve the issue.Use a soft cloth or brush to wash away any debris, then apply a lubricant that is suitable to ensure that they move freely.


Be sure to inspect the area surrounding the door. There are occasions when objects within the garage might drop or move, creating obstacles for the door. Be sure that there are no obstructions and there are none of the objects that could block the door.


Make sure the sensors are working if the door is not opening after removing any obstructions.

The sensors in modern garage doors can malfunction when they're dirty or not aligned properly.

When confronted with a garage door that suddenly isn't working, looking for obstructions or other debris is a sensible and usually successful first step.It takes only a few tools and experience, but it can save you money, time and also the hassle of calling a professional for what could be a straightforward fix.By keeping a clear path and

Inspect the Remote Control and Wall Switch


It is important to verify the wall switch and remote control.

Examining these components can help you to save time and avoid costly errors.

First, consider the remote control.This handheld device is your primary tool for operating the garage door without direct physical interaction.Over time, remote controls can experience issues such as drained batteries, signal interference, or even internal damage.Start by replacing the batteries with new ones.It might seem simple, but dead batteries are a common reason for a garage door not responding.If the problem persists after replacing the batteries, try reprogramming the remote according to the manufacturer's instructions.Additionally, ensure that the remote is within the recommended range and that there are no obstructions blocking the signal.


The wall switch is an essential component of the garage door's installation.

The wall switch is connected to the garage door opener and often provides a more reliable means for operation.Inspect the switch for any signs of physical damage, or wear.Sometimes loose wires, or faulty connections can make the switch malfunction.If you are able to do this, make sure you open the switch panel and check for any damaged or broken wires.If any issues are found it is possible to call an electrician professional to resolve the issue.

The wall switch or the remote control could be functioning properly, but the door is still not responding. This could be a sign of a problem with the garage opener unit, or related components, like sensors or door tracks.

It lets you identify these common problems before moving on to more complicated troubleshooting strategies.

The final step is to examine the remote control and wall switch in the event that your garage door suddenly stops functioning is a sensible and simple approach.By addressing these components first, you can quickly determine if the issue lies within these easily accessible parts or if further examination is needed.This initial inspection will not only help you save time, but also provides peace of mind knowing that you've completed the steps necessary to pinpoint the issue in a timely manner.

Test the door balance manually


When the garage door stops functioning it could be difficult as well as inconvenient.The garage door is a vital part of your home, providing security, protection from the elements, and a simple access to your car and storage area.

The most important step to consider when you encounter an issue with your garage door is to test manually the door balance.This simple, yet powerful procedure will help identify potential problems and prevent further damage to the door or any of its components.

The balance of a garage door is crucial for its efficient functioning.A properly balanced door makes sure that the opener won't have to work harder than it has to, reducing the possibility of wear and tear on the motor and other parts.An uneven door, in contrast can cause significant problems over time, like misalignment, broken springs, or even a complete system failure.Therefore conducting a test of the door's balance is a vital test that will assist in determining whether there is a problem with the door or the opener mechanism.


Start by disengaging the garage door opener.

The majority of garage doors come with a release mechanism, often the handle or red cord that lets you remove the door from the motor.Once the door is unlocked, carefully lift it manually to about waist height, then let it go. it.A well-balanced door will remain in place or move slowly.If the door is falling fast or jumps up this indicates an imbalance.

If you observe that the door isn't properly balanced it is essential to address the issue promptly.Door balance problems are typically related to the tension of springs. They could be risky to adjust by yourself due to the extreme tension they're under.It is advisable to consult a professional for assistance in adjusting the springs to ensure that the door is balanced correctly.Doing this does not just solve the immediate issue, but will increase the longevity and stability of the garage door system.


Manually testing the balance of the garage door is a critical first step to make if it suddenly stops working.

By addressing issues quickly and recognizing the importance of each in addressing the issue, you can make sure that your garage door will function seamlessly and safely in future.

Review the Tracks and Rollers.

This simple check will save you money and time If your garage door not working.


Tracks and rollers are essential elements of your garage door's operational system.The tracks comprise the metallic rails that control the door when it opens and closes, while the rollers are the small wheels that travel along the tracks.

These components can get dirty, wear out or misaligned over time. This can cause malfunctions.

Begin by examining the tracks for obstructions.Dust or grime and even small debris can accumulate within the tracks, causing the rollers' to be hampered as they move across the path.Cleaning the tracks with a damp cloth can often resolve these issues.Make sure that you dry them completely following the cleaning process to stop rust from forming.


After that, you should check the alignment of the tracks.Tracks must be straight and parallel to one other.If they look bent or out of alignment, the door could jam.You can gently press the misaligned parts back into position using an rubber mallet.However in the event that the damage is severe then it is recommended to consult a professional to adjust the tracks in a way that is safe and function.


The inspection of the rollers is equally important.Over time, they can wear out or become damaged particularly if constructed out of plastic.

Find evidence of wear and tear, such as cracks, or chips.If the rollers seem worn, think about replacing them with new ones.Metal rollers equipped with ball bearings usually offer more durability and smoother operation.

Additionally, lubrication also plays a vital role in maintaining the smooth motion of the tracks and rollers.Applying a silicone-based lubricant can lessen friction and help prevent wear.Make sure to lubricate all moving parts, including the hinges and springs, to ensure that your garage door is operating efficiently.


To conclude, taking a look at the tracks and rollers is a sensible first step if your garage door suddenly ceases working.It's an easy process that will usually identify and resolve the most common issues.By ensuring these components are in good condition, aligned and well-lubricated you can typically bring your garage door back to its full function without the need for expensive repairs.

It is important to check and maintain regularly the parts will help avoid problems in the future, and prolong the life of your garage door's system.

Check for visible damage or wear

It can be frustrating and inconvenient when the garage door stops operating abruptly, especially if you're heading home or trying to secure your home for the night.


The garage door is a complicated device made of multiple parts, like springs cables as well as rollers and tracks each one of which plays vital roles in the smooth operation.Over time, these components will wear out because of regular usage and exposure to environmental factors.

When you conduct a thorough inspection, you can identify any obvious indications of damage that could be creating problems for the door.

Begin by checking the springs, which are crucial for the lifting and lowering of the door.Look for any indications of breakage, rust, or misalignment.A broken or worn-out spring could render the door inoperable and it is essential to fix the issue promptly.Next proceed to the cables, and be sure to check for damaged or frayed strings that could hinder the door's movement.Similarly check the tracks and rollers for any dents, debris or obstructions that might be hindering the door's path.


Another area to focus on is the door itself.Look for any obvious damages, bends or warping that may affect its stability and alignment.Pay attention to the weather stripping that is located at the top of the door since damaged strips can stop the door from sealing properly.

Make sure that the sensors at the door are clear and in good alignment. Uneven or dirty alignment could cause the sensors to fail and stop working.

An inspection of the visuals is helpful however it's essential to keep in mind that not all issues are instantly apparent. If you don't notice any obvious signs of damage or wear, it's possible to talk an expert to identify the problem.


This method will not only enable you to identify the issue faster, but it will allow you to take actions to restore your garage door's proper function.

Being proactive and vigilant to your garage door's needs, you can guarantee the durability and longevity of the garage door.

Check for Springs and Cables

If your garage door stops working it could be annoying as well as inconvenient.One of the most vital steps you need to take in this situation is to check the springs as well as cables.These components are vital to the functionality of your garage door and problems related to them are typically the root cause behind malfunctioning door.


The springs play a crucial function in the operation and smoothness of your garage through helping to balance the load. There are two major spring types, extensions and torsion. Torsion springs mount above the garage, and they twist to conserve energy. Extension springs on the other hand are installed on to either side of the door and are stretched to supply the required force.

These springs are prone to get worn out and break, or lose tension, causing operational issues.

The cables could be damaged by wear and tear. They may fray or snap under pressure.


If you're unsure if the cables or springs need to be adjusted, visual check them. Find signs of wear and rust.


It's essential to consider safety when dealing with garage door parts.

Cables and springs are held at intense tension, and may cause serious injuries should they be mishandled.If you're not a pro at garage repair, it's best to speak with an experienced technician.They have the right tools and knowledge to replace or repair these parts to ensure your garage door operates properly and securely.

In conclusion, when your garage door suddenly stops working, assessing the springs and cables is a key step in diagnosing the problem.Understanding their role and potential issues can help you determine whether a simple adjustment is needed or if professional intervention is required.Taking prompt action not only restores functionality but also ensures the safety and longevity of your garage door system.

You should contact a professional Technician


Garage doors can suddenly stop working and cause you to be delayed. It could cause your home to be at risk.

What is the #1 Thing You Should Do When Your Garage Door Stops Working? - Southern Illinois

  1. Iowa
  2. bus
  3. Cairo

It may be tempting to get an instrument box to attempt a fix on your own however, it is recommended to seek out an expert. This choice is not just about your safety, but also provide a lasting and more effective solution.

Garage doors are complex systems composed of various components such as springs, cables, tracks, and electronic parts.Each of these elements plays a crucial role in the door's operation, and a malfunction in any part can cause the entire system to fail.Without proper knowledge and experience, attempting to fix these issues can be dangerous.For instance, garage door springs are under high tension and can cause severe injury if handled improperly.Professional technicians are trained to deal with these risks safely, using the right tools and techniques to handle repairs.


Furthermore, a skilled technician provides expertise and experience the average person simply doesn't have.

They can quickly diagnose the issue and identify whether it's a minor problem, like a misaligned track, or something more serious, like a broken spring.This expertise not only saves you time but also prevents the potential for further damage that can occur with incorrect handling.Professionals also have access to high-quality parts and can ensure that replacements match the specifications of your existing garage door system, leading to better functionality and longevity.

Additionally having a professional on your team can save you money over the long run.While DIY is a good option, while a DIY option may appear cheaper initially, the risk of mistakes is high. This could result in expensive and more costly repairs in the future.A professional technician will do the job exactly the first time to reduce the likelihood of issues recurring.

A lot of technicians offer warranties on their work, that gives you peace of mind knowing that should something go wrong, you are covered.

A expert can save you considerable time and hassle.Trying to learn the intricacies of garage door mechanics, buy the right tools, and carry out repairs can be time-consuming and take days.In contrast, a technician will often be able to resolve the issue in a short time, allowing you to go back to normal without delay.

What is the #1 Thing You Should Do When Your Garage Door Stops Working? - Southern Illinois

  1. Southern Illinois
  2. public election
  3. loading dock


In conclusion, while the desire to repair your garage door yourself might be overwhelming, a call to a professional technician is the safest option, the most efficient, and in the end, the most sensible option.Their knowledge, expertise in locating quality parts, and their ability to perform swift and accurate repairs will ensure that your garage door is back and running at a high level, protecting both your home and

Garage Door Talks

More Info:

How to reach us:


More about us:

Citations and other links

Village of Mokena
The gable bank barn at the historic McGovney–Yunker Farmstead
The gable bank barn at the historic McGovney–Yunker Farmstead
Flag of Village of Mokena
Official seal of Village of Mokena
Motto(s): 
Planned Progress, Pleasant Living
Location of Mokena in Will County, Illinois.
Location of Mokena in Will County, Illinois.
Location of Illinois in the United States
Location of Illinois in the United States
Coordinates: 41°32′04″N 87°52′37″W / 41.534414°N 87.876873°W / 41.534414; -87.876873
CountryUnited States
StateIllinois
CountyWill
TownshipFrankfort, New Lenox
Incorporated1880
Government
 • TypeVillage
Area
 • Total8.68 sq mi (22.47 km2)
 • Land8.68 sq mi (22.47 km2)
 • Water0.00 sq mi (0.00 km2)
Population
 (2020)
 • Total19,887
 • Density2,292.19/sq mi (885.05/km2)
Time zoneUTC-6 (CST)
 • Summer (DST)UTC-5 (CDT)
ZIP code
60448[2]
Area codes708
FIPS code17-49854
Websitehttp://www.mokena.org/

Mokena (/mˈkinə/ moh-KEE-nuh) is a village in Will County, Illinois, United States. It is a southwest suburb of Chicago. The population was 19,887 at the 2020 census. The Census Bureau's 2019 estimate found that the population had increased to 20,159.[3]

Etymology

[edit]

Mokena is a name apparently derived from a Native American language meaning "turtle".[4] While the particular language from which the name originates is not documented, likely candidates are Anishinaabemowin, whose word for "snapping turtle" is mikinaak,[5] and its close sister language Potawatomi, in which the same animal is called mkenak.[6] Both languages were once spoken in the area now occupied by the town.

Mokena is located at 41°32′4″N 87°52′37″W / 41.53444°N 87.87694°W / 41.53444; -87.87694.[7] According to the 2010 census, Mokena has an area of 8.893 square miles (23.03 km2), of which 8.89 square miles (23.02 km2) (or 99.97%) is land and 0.003 square miles (0.01 km2) (or 0.03%) is water.[8] It is bordered by Tinley Park to the northeast, Orland Park to the north, Homer Glen to the northwest, Frankfort to the south and New Lenox to the west.

Education

[edit]

Elementary school services are provided by one of four school districts: Mokena School District 159, New Lenox School District 122, Frankfort School District 157C, and Summit Hill School District 161. Schools within District 159 include MES (Mokena Elementary School), MIS (Mokena Intermediate School), and MJHS (Mokena Junior High School). Mokena is served by Lincoln-Way Community High School District 210; students living in districts 159 or 122 attend Lincoln-Way Central High School, and students living in districts 157C or 161 attend Lincoln-Way East High School. Higher education is provided at Joliet Junior College, the nation's first public community college, and at Rasmussen College.

Demographics

[edit]
Historical population
CensusPop.Note
1880522
1890364−30.3%
1900281−22.8%
191035927.8%
192047532.3%
193056218.3%
194065716.9%
195090337.4%
19601,33247.5%
19701,64323.3%
19804,578178.6%
19906,12833.9%
200014,583138.0%
201018,74028.5%
202019,8876.1%
U.S. Decennial Census[9]

As of the census[10] of 2010, there were 18,740 people, 6,358 households, and 5,120 families residing in the village. The population density was 2,432.4 inhabitants per square mile (939.2/km2). There were 4,848 housing units at an average density of 808.6 per square mile (312.2/km2). The racial makeup of the village was 94.5% White, 1.3% African American, 0.01% Native American, 2.0% Asian, 0.01% Pacific Islander, 0.9% from other races, and 0.63% from two or more races. Hispanic or Latino of any race were 4.8% of the population.

As of the census of 2000, there were 4,703 households, out of which 48.5% had children under the age of 18 living with them, 73.7% were married couples living together, 7.3% had a female householder with no husband present, and 16.8% were non-families. 14.0% of all households were made up of individuals, and 3.3% had someone living alone who was 65 years of age or older. The average household size was 3.10 and the average family size was 3.46.

In the village, the population was spread out, with 32.4% under the age of 18, 7.1% from 18 to 24, 32.7% from 25 to 44, 21.5% from 45 to 64, and 6.2% who were 65 years of age or older. The median age was 34 years. For every 100 females, there were 101.5 males. For every 100 females age 18 and over, there were 97.3 males.

The median family income is $82,596 and the median income for a household is $91,817. Males had a median income of $58,226 versus $31,522 for females. The per capita income for the village was $31,944. As of 2008, the median house value was $350,130, up from $211,300 in 2000.[11]

About 0.7% of families and 1.0% of the population were below the poverty line, including 0.6% of those under age 18 and 4.6% of those age 65 or over.

Transportation

[edit]

The Village of Mokena is serviced by the Metra rail service Rock Island District. Mokena has two commuter rail stations, Hickory Creek and Front Street, providing service to downtown Chicago's LaSalle Street Station, connecting with components of the Chicago Transit Authority. Mokena is also served by I-80, which runs along its northern border. Through I-80 commuters have convenient access to I-355 (Veteran's Memorial Tollway) and I-57. The main north–south thoroughfares are US Route 45 (LaGrange Rd) and Wolf Rd. The main east–west thoroughfares are 191st St, LaPorte Rd., and US Route 30 (Lincoln Highway). Rail freight traffic travels along both the Metra RI District Railway (Metra RI) and the Canadian National Railway (CN). The CN tracks run east/west along Mokena's southern boundary, while the Metra Rock Island District (Metra) tracks approximately bisect the town in a northeastern/southwestern direction.

Notable people

[edit]

References

[edit]
  1. ^ "2020 U.S. Gazetteer Files". United States Census Bureau. Retrieved March 15, 2022.
  2. ^ "Mokena IL ZIP Code". zipdatamaps.com. 2023. Retrieved January 26, 2023.
  3. ^ "2010 Census Interactive Population Search". Archived from the original on June 15, 2016. Retrieved December 6, 2017.
  4. ^ Gannett, Henry (1905). The Origin of Certain Place Names in the United States. U.S. Government Printing Office. p. 211.
  5. ^ "The Ojibwe People's Dictionary". ojibwe.lib.umn.edu. Retrieved January 7, 2021.
  6. ^ "Potawatomi Language Dictionary - View Word". potawatomidictionary.com. Retrieved January 7, 2021.
  7. ^ "US Gazetteer files: 2010, 2000, and 1990". United States Census Bureau. February 12, 2011. Retrieved April 23, 2011.
  8. ^ "G001 - Geographic Identifiers - 2010 Census Summary File 1". United States Census Bureau. Archived from the original on February 13, 2020. Retrieved December 19, 2015.
  9. ^ "Census of Population and Housing". Census.gov. Retrieved June 4, 2015.
  10. ^ "U.S. Census website". United States Census Bureau. Retrieved January 31, 2008.
  11. ^ "Mokena, Illinois (IL 60448) profile: population, maps, real estate, averages, homes, statistics, relocation, travel, jobs, hospitals, schools, crime, moving, houses, news, sex offenders". www.city-data.com.
  12. ^ "Boers: Leaving Home Produces Rush Of Vivid Memories". December 23, 2014. Retrieved January 4, 2020.
  13. ^ Sherdog.com. "Jason Guida MMA Stats, Pictures, News, Videos, Biography - Sherdog.com". Sherdog. Retrieved January 4, 2020.
  14. ^ 'Don C. Hall, 87, Veteran Show Trouper, Dies,' Stevens Point Daily Journal, October 29, 1953, pg. 15
  15. ^ "Ron Kittle: Renaissance Man | Chicagoly Magazine". Archived from the original on June 22, 2019. Retrieved June 22, 2019.
  16. ^ Sotonoff, Jamie (August 30, 2011). "Denise Richards: Suburban upbringing kept me grounded". Daily Herald.
[edit]

Sectional garage door
Up-and-over garage door
Torsion springs, drums, cables, end bearing plates, center bearing plate and rolloers (wheels) all hardware needed for a functional garage door.
Garage Door Hardware

A garage door is a large door to allow egress for a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. The operating mechanism is usually spring-loaded or counterbalanced to offset the door's weight and reduce the human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss.

Description

[edit]
An electric garage door opener operates on the center track

A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with an unequal parallelogram-style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (180 kg) or more but is balanced by either a torsion spring system or a pair of extension springs.[2] A garage door opener is controlled motorized mechanism for opening garage doors adds convenience, safety, and security often used with a remote or a button on wall.[3]

History

[edit]

The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the United States, they arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]

Types

[edit]

Single panel garage doors

[edit]
jamb type hardware
one piece track type hardware

Single-panel doors are constructed from one monolithic panel. A single panel door swings up and overhead with a hinge on each side (jamb-type hardware) to a fully open position from the closed position. A disadvantage of monolithic panel doors is that the swing-up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.

Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (mounted at the top of the wood frame) and a roller mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of the garage door. Using track hardware, a car can be parked much closer to the door, as the door is positioned entirely inside the garage door header when in the open position. Track-type hardware has less arc when raising and lowering the garage door than jamb-type hardware.[citation needed]

Sectional garage doors

Sectional doors usually have three to eight panels and slide up and overhead. Sectional doors occupy the same internal garage space as a monolithic door. Sectional doors have two advantages over single-panel monolithic doors:

  • Sectional doors do not require any space outside the garage to open. A vehicle may park very close to the garage before opening the door.
  • Each panel of a sectional door has its connection to the door track. This increases reliability and robustness compared to monolithic doors, which have only a few track connections for the whole panel.

Garage doors can be made of many materials, but steel, aluminum, wood, copper, glass, and vinyl (polyethylene) are the most popular materials. Some manufacturers incorporate foamed-in-place polyurethane insulation within the monolithic panel and sectional garage doors.

The side sliding sectional door[5]

  • A lot of space under the garage ceiling.
  • Can use the entire ceiling of the garage.
  • Fast access to the garage

Roller doors

[edit]
Detail of roller door mechanism
Industrial tents with rollup overhead doors

Roller doors (sometimes called "sheet doors") are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g., transparent corrugated fiberglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single-car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Oversized roller doors in commercial premises are not sprung (except in the US), and a manual pulley and chain system or a geared motor is used to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.

In the UK (and other parts of the EU), 'insulated' roller garage doors are available, using an aluminum lathe filled with polyurethane foam for thermal and acoustic insulation.

Concerning thermal insulation, the roller door has a typical insulation R-value of 4.9 to 5.2. A sheet steel garage door has a typical insulation R-value of 0.5 to 2.7.

An application that needs more thermal insulation typically uses a foam-filled sectional garage door, which provides typical insulation R-values of 6.1 to 6.4.

Garage door materials

[edit]
  • Aluminum garage doors are usually found in commercial settings and are uncommon for residential ones. Aluminum is typically only used for full-view garage doors (doors that are made up of glass sections divided by aluminum stiles). Aluminum doors are rust-proof and low maintenance.
  • Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They also have polyurethane insulated base sections or other types of foam insulation. These premium doors can match steel garage doors and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units. Fiberglass doors are commonly used near an ocean, where salt water can ruin regular steel doors.
  • Steel doors have a variety of sizes and styles, provide strength and security, are cost-competitive, and may have optional insulating value. Extra strength is available with two or three layers of galvanized steel with a low gauge number (0.6 - 0.7 mm steel panels).[6]
  • Wood garage doors offer aesthetic appeal, but they are high maintenance and may be expensive. Low-priced wood garage doors may warp and break easily.

Steel stamped construction

[edit]
Sectional-type steel with exterior cladding overhead garage doors in the style of old carriage house doors

A common material for a new garage door is a steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and a three-layer door, also known as a sandwich-style door. A design mimicking carriage house doors has become popular since the early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.

Insulation

[edit]

In situations involving residential attached garages, the insulating value and the energy efficiency of a garage door are essential to avoid overheating and freezing problems, as well as for comfort and energy savings.

Torsion spring lift mechanism

[edit]

A torsion spring counterbalance system consists of one or two tightly wound-up springs on a steel shaft with cable drums at both ends. The apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs consist of a steel wire with a stationary cone at one end and a winding cone at the other. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind, and the stored tension lifts the door by turning the shaft, thus turning the cable drums and wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums, and the springs are rewound to full tension.

Life of torsion spring

[edit]

Garage door manufacturers typically produce doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000-cycle spring. However, it is essential to remember that if the garage door's weight is increased by adding glass, additional insulation, or even several coats of paint, the torsion spring's life may be significantly reduced. Additionally, springs in highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.

Other factors like poor garage door maintenance, loose tracks, or components shorten torsion spring life. Owners are advised to avoid applying grease to garage door tracks because that makes the wheels "skate" in the track instead of turning on their bearings. Only bearings, hinges, and spring wire require lubricant.

Extension spring lift mechanism

[edit]

An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically, these springs are made of 11 gauge (3 mm) galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.

Maintenance

[edit]

Maintenance of garage doors is described in the manufacturer's instructions and consists of periodic checks for correct operation, visual inspection of parts, and lubrication. [7][8]

Safety

[edit]

Garage doors can cause injury and property damage (including expensive damage to the door itself) in several ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings, and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on torsion spring systems).

A garage door with a broken spring or the wrong strength can fall. Because the effective mass of the door increases as the garage door sections transfer from the horizontal to vertical door tracks, a falling garage door accelerates rapidly. A free-falling garage door can cause severe injury or death.

The sections and rollers on garage doors represent a significant pinch hazard. Children should never be allowed near a moving garage door for this reason. On manually operated garage doors, handles should be installed vertically to promote "vertical orientation of the hand".

Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. Modern openers have “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lb (10 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door-related property damage, can be avoided by following these precautions.[9]

Certain parts, especially springs, cables, bottom brackets, and spring anchor plates, are under extreme tension. Injuries can occur if parts under tension are removed.

Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. The safety cable prevents hazards to bystanders when a spring, pulley, or cable breaks under tension and makes the system relatively safe.

Torsion spring systems can be hazardous as they are always under tension and release energy when the spring fails. Severe injury or death can be caused by the projectile pieces of a failed torsion spring. Many people have been injured or killed trying to adjust torsion springs, and special training and procedures are required to modify a torsion spring safely; it is a job for a professional, not a homeowner or DIYer.

References

[edit]
  1. ^ a b Hamilton, Gene; Hamilton, Katie (2004). Do it right the first time: what every homeowner needs to know before the work begins. Innova Publishers. p. 154. ISBN 9780974937359. Retrieved 2015-07-19.
  2. ^ Ask the Family handy-man. Reader's Digest. 1999. p. 138. ISBN 9780762101429. Retrieved 2015-07-19. garage door can weigh 400 pounds or more; they only seem light because the springs balance the weight as you lift the door.
  3. ^ Day, Richard (July 1982). "Tips from a pro: how to install a garage-door opener". Popular Science. Vol. 221, no. 1. pp. 91–93. Retrieved 2015-07-19.
  4. ^ a b Winterton, Deanne (2012-02-21). "History of the Garage Door". Amazines.com. Retrieved 2015-07-19.
  5. ^ Deziel, Chris (10 October 2023). "Are Sliding Garage Doors the Best Option for You?". Family Handyman. Retrieved 3 February 2024.
  6. ^ "DASMA Metal Gauge Chart Technical Data Sheet #154" (PDF). DASMA. Archived from the original (PDF) on 2014-08-02. Retrieved 2015-07-19.
  7. ^ "DASMA Door and Access Systems Manufacturers Association". Dasma.com. 1993-01-01. Archived from the original on 2012-10-28. Retrieved 2012-11-04.
  8. ^ "DASMA Door and Access Systems Manufacturers Association". Dasma.com. Archived from the original on 2012-08-26. Retrieved 2012-11-04.
  9. ^ "How Important Are Garage Door Safety Sensors". rsvallejo.com. Retrieved 2023-04-06.
[edit]

Media related to Garage doors at Wikimedia Commons


A residential garage door opener. The motor is in the box on the upper-right.

A garage door opener is a motorized device that opens and closes a garage door controlled by switches on the garage wall. Most also include a handheld radio remote control carried by the owner, which can be used to open and close the door from a short distance.

The electric opener

[edit]

The electric overhead garage door opener was invented by C.G. Johnson in 1926 in Hartford City, Indiana.[1] Electric Garage Door openers did not become popular until Era Meter Company of Chicago offered one after World War II where the overhead garage door could be opened via a key pad located on a post at the end of the driveway or a switch inside the garage.[2]

As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise, they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.

The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]

The entire assembly hangs above the garage door. The power unit hangs from the ceiling and is located towards the rear of the garage. The end of the track on the opposite end of the power unit attaches to a header bracket that is attached to the header wall above the garage door. The powerhead is usually supported by punched angle iron.

Recently another type of opener, known as the jackshaft opener, has become more popular.[when?] This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.

Types

[edit]

There are five types of garage door openers:

  1. Chain drive openers. These have a chain (similar to a bicycle's) that connects the trolley to the motor.
  2. Belt drive openers use a rubber belt in place of a chain.
  3. Screw drive openers have a long screw inside the track. The trolley connects to this screw.
  4. Direct drive openers have the motor installed inside the trolley and use a gear wheel to guide the trolley along a fixed chain.
  5. Jackshaft openers mount on the wall at either end of the torsion bar.

Remote control

[edit]

The first wireless garage door openers were invented and developed by two US inventors at the same time, one in Illinois and the other in Washington state, around 1930. They were unknown to each other.[4]

The first garage door opener remote controls were simple and consisted of a simple transmitter (the remote) and receiver which controlled the opener mechanism. The transmitter would transmit on a designated frequency; the receiver would listen for the radio signal, then open or close the garage, depending on the door position. The basic concept of this can be traced back to World War II. This type of system was used to detonate remote bombs. While novel at the time, the technology ran its course when garage door openers became popular. While the garage door remote control transmitter is low power and has limited range, its signal can be received by other, nearby, garage door openers. When two neighbors had garage door openers, then opening one garage door might open the neighbor's garage door as well.

The second stage of the wireless garage door opener system solved the opening-the-neighbor's-garage-door problem. The remote controls on these systems transmitted a digital code, and the receiver in the garage responded only to that code. The codes were typically set by eight to twelve DIP switches on the receiver and transmitter, so they allowed for 28 = 256 to 212 = 4,096 different codes. As long as neighbors used different codes, they would not open each other's garage doors. The intent of these systems was to avoid interference with nearby garage doors; the systems were not designed with security in mind. Intruders were able to defeat the security of these systems and gain entry to the garage and the house. The number of codes was small enough that even an unsophisticated intruder with a compatible remote control transmitter could just start transmitting all possible codes until he found one that opened the door. More sophisticated intruders could acquire a black box master key that automatically transmitted every possible code in a short time. An even more sophisticated method is known as a replay attack. The attacker would use a code grabber, which has a receiver that captures the remote's digital code and can retransmit that digital code at a later time. The attacker with a code grabber would wait nearby for the homeowner to use his remote, capture the code, and then replay the code to open the door when the homeowner was gone. Multicode openers became unpopular in areas where security was important, but due to their ease of programming, such openers are often used to operate such things as the gates in gated apartment complexes.

An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. A large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes but was still vulnerable to the replay attack.

The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.

The fourth stage of garage door opener systems is similar to third stage, but it is limited to the 315 MHz frequency. The 315 MHz frequency range avoids interference from the land mobile radio system (LMRS) used by the U.S. military.

The following standards are used by units manufactured by Chamberlain (including LiftMaster and Craftsman):

Dates System Color of programming button and LED on unit Color of LED on remote*
1984–1993 8-12 DIP switch on 300-400 MHz white, gray, or yellow button with red LED red
1993–1997 Billion Code on 390 MHz green button with green or red LED green
1997–2005 Security+ (rolling code) on 390 MHz orange or red button with amber LED amber or none
2005–present Security+ (rolling code) on 315 MHz purple button with amber LED none
2011–present Security+ 2.0 (rolling code) on 310, 315, and 390 MHz yellow button with amber LED and yellow antenna wires red or blue

* Does not apply to keyless entry keypads or universal remotes.

Recent Chamberlain garage door openers that have Security+ 2.0 features also use a special serial protocol on wired connections rather than a simple switch closure.[5]

The following standards are used by units manufactured by Overhead Door Corporation and its subsidiary The Genie Company†:

Dates System
1985–1995 9–12 DIP switch on 360, 380, or 390 MHz[6][7]
1995–2005 Intellicode/CodeDodger (rolling code) on 390 MHz
2005–present Intellicode/CodeDodger (rolling code) on 315 MHz
2011–present Intellicode 2/CodeDodger 2 (rolling code) on 315 and 390 MHz

Note: There are no standard color codes for the learn button or LED on units manufactured by Overhead Door or Genie. All accessories made for later versions of Genie Intellicode and Overhead Door CodeDodger are backward compatible with previous generations of Intellicode and CodeDodger.

Cloning garage door opener remotes

[edit]
A typical photo of both the outer case and inner circuit of a garage door opener remote control.

Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.

Additional features

[edit]

Additional features that have been added over the years have included:

  • Automatic courtesy lights that turn on when the door opens (or via motion sensors) and automatically turn off after a preset delay
  • A remote lockout feature, which turns off the radio receiver while one is on vacation or away for an extended time.
  • The availability of accessories has increased, including such features as wireless keypads, key chain remotes, and solenoid-operated deadbolts to lock the door itself.
  • Automatic door closing feature, which after a fixed time by the owner, closes the garage door to prevent theft.

More sophisticated features are also available, such as an integrated carbon monoxide sensor to open the door in case of the garage being flooded with exhaust fumes. Other systems allow door activation over the Internet to allow home owners to open their garage door from their office for deliveries.

Another recent innovation in the garage door opener is a fingerprint-based wireless keypad. This unit attaches to the outside of the garage door on the jamb and allows users to open and close their doors with the press of a finger, rather than creating a personal identification number (PIN). This is especially helpful for families with children who may forget a code and are latchkey kids.

Safety

[edit]
Electric eye for safety

The garage door is generally the largest moving object in a home. An improperly adjusted garage door opener can exert strong and deadly forces and might not reverse the garage door in an emergency. The manufacturer's instructions provide guidance to the user on the proper adjustment and maintenance of the opener.

Garage door openers manufactured and installed in the United States since 1982 are required to provide a quick-release mechanism on the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment.[8] Garage door openers manufactured since 1991 are also required to reverse the garage door if it strikes a solid object.[9][10]

In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path.[12][13]

California Senate Bill No. 969

[edit]

In California, Senate Bill No. 969 requires that any automatic residential garage door opener that is manufactured for sale, sold, offered for sale, or installed in a residence to have a battery backup function that is designed to operate when activated because of an electrical outage.[14] The bill went into effect on July 1, 2019. Under the bill, any automatic garage door opener that is in violation is subject to a civil penalty of $1000.

The bill was passed by Gov. Jerry Brown on Sept. 21, 2018, in response to the 2017 California Wildfires in which at least 5 individuals lost their lives because they could not open their garage door when the power went out.[15]

The Door and Access Systems Manufacturers Association International opposed the bill arguing that garage door openers with backup batteries require regular maintenance and that the bill should be amended to make this clear. In addition, they said that "garage door openers with backup batteries are not designed to serve as life safety devices, and should not be relied upon to prove a means of egress from a garage during an electrical outage."[16]

The bill passed, despite most garage doors having a release pull cord.

References

[edit]
  1. ^ Robert J Girod (2014). "Garage Door Openers - High-tech Burglary". Advanced Criminal Investigations and Intelligence Operations: Tradecraft Methods, Practices, Tactics, and Techniques. Taylor and Francis. p. 90. ISBN 9781482230741.
  2. ^ "Aids To Modern Living - Garage Doors". Popular Science: 137. December 1946.
  3. ^ Castro, Diane. "The Complete Garage Door System". Regency Conference Center. Retrieved 10 March 2020.
  4. ^ "Widely Separated Inventors Invent Garage Door Openers By Radio Impulses". Popular Science: 32. February 1931.
  5. ^ "Will my older accessories work with the new line of Security+ 2.0 garage door openers?". alldaygaragerepair.com. Retrieved 2017-06-23.
  6. ^ Willmes, Dave. "My Overhead Door Opener Doesn't Work with this Universal Remote". www.overheaddooronline.com. Retrieved 20 October 2016.
  7. ^ "FCC ID BSH8YN106546 by Overhead Door Corporation". FCCID.io. Retrieved 20 October 2016.
  8. ^ "Falling Garage Doors — A Crushing Concern". Garage Door Child Safety.
  9. ^ "Non Reversing Garage Door Openers a Hazard" (PDF). U.S. Consumer Product Safety Commission.
  10. ^ "Garage Door System Safety Guidelines". Door & Access Systems Manufacturers Association International. Archived from the original on 2008-12-23.
  11. ^ Garage Door Operators • CPSC
  12. ^ Non-Reversing Automatic Garage Door Openers Are a Hazard • CPSC
  13. ^ 16CFR1211
  14. ^ "Bill Text - SB-969 Automatic garage door openers: backup batteries". leginfo.legislature.ca.gov. California Legislative Information. Retrieved 6 September 2019.
  15. ^ "New California Law Could Cost You $1000 in Fines". Clark's Garage Door. 4 September 2019. Retrieved 6 September 2019.
  16. ^ "California Mandates Battery Backup With All GDOS - Experts Cite Problems With The Legislation" (PDF). dasma.com. DASMA. Retrieved 6 September 2019.
[edit]

Driving Directions in Will County to


Driving Directions From Chillin' Products to
Driving Directions From Red Roof Inn Chicago - Joliet to
Driving Directions From Clarion Hotel & Convention Center Joliet to
Driving Directions From Golden Corral Buffet & Grill to